The key piece of legislation for people who work at potentially dangerous heights in Great Britain is The Work at Height Regulations 2005. As stated on the HSE website, this legislation was put in place "to prevent death and injury caused by a fall from height". The regulations state that work at height must be:

• Properly planned
• Appropriately supervised
• Carried out in a safe manner by competent personnel only

Interestingly, the 2005 regulations do not specify any particular equipment that must be used when working at height - they simply state the need for "sufficent work equipment" and remind employers that, when selecting appropriate height safety equipment for any given task, they must take account of working conditions, fall distance, the duration of the job, and several other factors.

In a nutshell: the law doesn't state that you HAVE to use a safety harness or a fall arrest block, but you are required to have some kind of fall prevention system in place, and the aforementioned items are among the most commonly-used solutions. In the end, it is up to you to decide what kind of equipment is most appropriate for the task at hand.

What will happen if I don't use any height safety equipment?

If one of your employees suffers an accident whilst working at height, you may investigated by the Health and Safety Executive. If they decide that you neglected to provide the right safety equipment or otherwise failed to fulfil your duties as an employer (as prescribed by the 2005 regulations and several other pieces of legislation), you will likely be prosecuted, which can lead to hefty fines and even jail time.

So don't leave anything to chance! Plan your work properly, carry out a full risk assessment before starting, and always use the appropriate height safety equipment to minimise the risk of a fall.

Further Reading: Height Safety Checklist

The key piece of legislation for people who work at potentially dangerous heights in Great Britain is The Work at Height Regulations 2005. As stated on the HSE website, this legislation was put in place "to prevent death and injury caused by a fall from height". The regulations state that work at height must be:

• Properly planned
• Appropriately supervised
• Carried out in a safe manner by competent personnel only

Interestingly, the 2005 regulations do not specify any particular equipment that must be used when working at height - they simply state the need for "sufficent work equipment" and remind employers that, when selecting appropriate height safety equipment for any given task, they must take account of working conditions, fall distance, the duration of the job, and several other factors.

In a nutshell: the law doesn't state that you HAVE to use a safety harness or a fall arrest block, but you are required to have some kind of fall prevention system in place, and the aforementioned items are among the most commonly-used solutions. In the end, it is up to you to decide what kind of equipment is most appropriate for the task at hand.

What will happen if I don't use any height safety equipment?

If one of your employees suffers an accident whilst working at height, you may investigated by the Health and Safety Executive. If they decide that you neglected to provide the right safety equipment or otherwise failed to fulfil your duties as an employer (as prescribed by the 2005 regulations and several other pieces of legislation), you will likely be prosecuted, which can lead to hefty fines and even jail time.

So don't leave anything to chance! Plan your work properly, carry out a full risk assessment before starting, and always use the appropriate height safety equipment to minimise the risk of a fall.

Further Reading: Height Safety Checklist

We were recently presented with the task of designing and installing permanent access systems on the underside of Hastings Pier.

The pier suffered extensive fire damage in October 2010, destroying an estimated 95% of the superstructure. The Hastings Pier Charity was formed shortly afterwards, and funding was secured from the Heritage Lottery Fund, which enabled restoration work to commence in January 2014.

Due to the nature of this project, no steel sections were able to be drilled, so we at SafetyLiftinGear had to design and fabricate bespoke stainless steel brackets for the mounting of our permanent horizontal safety lines.

The safety lines will provide over 170 metres of safe access for engineers when completing future maintenance and inspections along the underside of the pier.

This project is yet another example of SLG's ability to provide a bespoke solution for any brief. Visit our Height Safety department or contact us now to get what you need for your project.

We were recently presented with the task of designing and installing permanent access systems on the underside of Hastings Pier.

The pier suffered extensive fire damage in October 2010, destroying an estimated 95% of the superstructure. The Hastings Pier Charity was formed shortly afterwards, and funding was secured from the Heritage Lottery Fund, which enabled restoration work to commence in January 2014.

Due to the nature of this project, no steel sections were able to be drilled, so we at SafetyLiftinGear had to design and fabricate bespoke stainless steel brackets for the mounting of our permanent horizontal safety lines.

The safety lines will provide over 170 metres of safe access for engineers when completing future maintenance and inspections along the underside of the pier.

This project is yet another example of SLG's ability to provide a bespoke solution for any brief. Visit our Height Safety department or contact us now to get what you need for your project.

Working at height can be very dangerous - we recently compiled a seven-point height safety checklist to outline some best practices, and then we added another three points just to make sure. In today's blog, we'd like to show you a few examples of how not to work safely at heights; let's see what lessons we can learn from these photographs...

Lesson #1 - Always wear a safety harness!

Lesson #2 - No haphazard pile of paint tins (or whatever else you have lying around) will ever be as safe as a properly-footed ladder.

Lesson #3 - No, seriously, you should be wearing a safety harness. What's to stop you from slipping and falling?

Lesson #4 - A ladder mounted on the scoop of a digger is no substitute for a cherry picker (depressingly, there are loads of other photos like this on the internet!)

Lesson #5 - PPE will only help you up to a point (we found this image on the HSE website, and as they pointed out, the hard hats and hi-vis jackets won't do much to protect those two men if they fall!)

Now that you've seen the mistakes that some people make, visit our Height Safety department and make sure you don't make them too!

As we've discussed previously, working at heights can be very dangerous, and failure to observe the proper safety regulations can lead to dire consequences. Height safety guidelines are in place to keep you from falling and, if you do fall, to prevent you from being badly hurt; you may feel that you are careful or sure-footed enough not to need a safety harness, but one slip is all it takes and it's never worth taking that risk.

With all of this in mind, we at SafetyLiftinGear would like to draw your attention to the following Height Safety Checklist. These safety precautions are recommended by the HSE (Health and Safety Executive), so you can rest assured that they were thought up with worker safety in mind.

Before working at height, ask yourself the following questions:

• Have I been properly trained to carry out this job? Do I have the correct permit to work?
  
  
• Will the current weather conditions have any impact on my safety while working at height?
  
  
• Have I chosen the best means of reaching the heights necessary to complete this job? Could I use a cherry picker instead of a ladder?
  
  
• Is this ladder safe? Is it in good condition? Is it tied, footed, or otherwise secured at the base? Is it long enough* for the job?
  
  
• Will I have to walk on a roof or another raised surface? If so, is this surface at all fragile? Is there any risk of falling through?
  
  
• Will I be able to avoid stepping on roof lights? Are all roof lights clearly visible?
  
  
• Do I need crawling boards to safely bridge joists?
  
  
• If I fall, what will prevent me from hitting the ground? Am I wearing a safety harness, and is it properly secured?
  
  
• Is there any chance that I will drop something to the ground below? Could this cause any damage? Should I be wearing a tool lanyard?
  
  
• If a fall or accident should occur, do I have a suitable rescue plan in place?

*To ensure worker safety, ladders should reach at least 0.9m (35 and a half inches) beyond the stepping-off point.

Visit SafetyLiftinGear's Height Safety department to ensure that you have everything you need to safely work at height.

As we've discussed previously, working at heights can be very dangerous, and failure to observe the proper safety regulations can lead to dire consequences. Height safety guidelines are in place to keep you from falling and, if you do fall, to prevent you from being badly hurt; you may feel that you are careful or sure-footed enough not to need a safety harness, but one slip is all it takes and it's never worth taking that risk.

With all of this in mind, we at SafetyLiftinGear would like to draw your attention to the following Height Safety Checklist. These safety precautions are recommended by the HSE (Health and Safety Executive), so you can rest assured that they were thought up with worker safety in mind.

Before working at height, ask yourself the following questions:

• Have I been properly trained to carry out this job? Do I have the correct permit to work?
  
  
• Will the current weather conditions have any impact on my safety while working at height?
  
  
• Have I chosen the best means of reaching the heights necessary to complete this job? Could I use a cherry picker instead of a ladder?
  
  
• Is this ladder safe? Is it in good condition? Is it tied, footed, or otherwise secured at the base? Is it long enough* for the job?
  
  
• Will I have to walk on a roof or another raised surface? If so, is this surface at all fragile? Is there any risk of falling through?
  
  
• Will I be able to avoid stepping on roof lights? Are all roof lights clearly visible?
  
  
• Do I need crawling boards to safely bridge joists?
  
  
• If I fall, what will prevent me from hitting the ground? Am I wearing a safety harness, and is it properly secured?
  
  
• Is there any chance that I will drop something to the ground below? Could this cause any damage? Should I be wearing a tool lanyard?
  
  
• If a fall or accident should occur, do I have a suitable rescue plan in place?

*To ensure worker safety, ladders should reach at least 0.9m (35 and a half inches) beyond the stepping-off point.

Visit SafetyLiftinGear's Height Safety department to ensure that you have everything you need to safely work at height.